The OpenNET Project / Index page

[ новости /+++ | форум | wiki | теги | ]

Поиск:  Каталог документации

Next Previous Contents

6. Software Configuration and Card Diagnostics

In most cases, if the configuration is done by software, and stored in an EEPROM, you will usually have to boot DOS, and use the vendor supplied DOS program to set the cards IRQ, I/O, mem_addr and whatnot. Besides, hopefully it is something you will only be setting once. If you don't have the DOS software for your card, try looking on the WWW site of your card manufacturer. If you don't know the site name, take a guess at it, i.e. `www.my_vendor.com' where `my_vendor' is the name of your card manufacturer. This works for SMC, 3Com, and many many other manufacturers.

There are some cards for which Linux versions of the config utils exist, and they are listed here. Donald has written a few small card diagnostic programs that run under Linux. Most of these are a result of debugging tools that he has created while writing the various drivers. Don't expect fancy menu-driven interfaces. You will have to read the source code to use most of these. Even if your particular card doesn't have a corresponding diagnostic, you can still get some information just by typing cat /proc/net/dev -- assuming that your card was at least detected at boot.

In either case, you will have to run most of these programs as root (to allow I/O to the ports) and you probably want to shut down the ethercard before doing so by typing ifconfig eth0 down first.

6.1 Configuration Programs for Ethernet Cards

WD80x3 Cards

For people with wd80x3 cards, there is the program wdsetup which can be found in wdsetup-0.6a.tar.gz on Linux ftp sites. It is not being actively maintained, and has not been updated for quite a while. If it works fine for you then great, if not, use the DOS version that you should have got with your card. If you don't have the DOS version, you will be glad to know that the SMC setup/driver disks are available at SMC's ftp site. Of course, you have to have an EEPROM card to use this utility. Old, old wd8003 cards, and some wd8013 clones use jumpers to set up the card instead.

Digital / DEC Cards

The Digital EtherWorks 3 card can be configured in a similar fashion to the DOS program NICSETUP.EXE. David C. Davies wrote this and other tools for the EtherWorks 3 in conjunction with the driver. Look on you local linux FTP site in the directory /pub/linux/system/Network/management for the file that is named ewrk3tools-X.XX.tar.gz.

NE2000+ or AT/LANTIC Cards

Some Nat Semi DP83905 implementations (such as the AT/LANTIC and the NE2000+) are software configurable. (Note that these cards can also emulate a wd8013 card!) You can get the file /pub/linux/setup/atlantic.c from Donald's ftp server, www.scyld.com to configure this card. In addition, the configuration programs for the Kingston DP83905 cards seem to work with all cards, as they don't check for a vendor specific address before allowing you to use them. Follow the following URL: Kingston Software and get 20XX12.EXE and INFOSET.EXE.

Be careful when configuring NE2000+ cards, as you can give them bad setting values which can cause problems. A typical example is accidentally enabling the boot ROM in the EEPROM (even if no ROM is installed) to a setting that conflicts with the VGA card. The result is a computer that just beeps at you when you turn it on and nothing appears on the screen.

You can typically recover from this by doing the following: Remove the card from the machine, and then boot and enter the CMOS setup. Change the `Display Adapter' to `Not Installed' and change the default boot drive to `A:' (your floppy drive). Also change the `Wait for F1 if any Error' to `Disabled'. This way, the computer should boot without user intervention. Now create a bootable DOS floppy (`format a: /s /u') and copy the program default.exe from the 20XX12.EXE archive above onto that floppy. Then type echo default > a:autoexec.bat so that the program to set the card back to sane defaults will be run automatically when you boot from this floppy. Shut the machine off, re-install the ne2000+ card, insert your new boot floppy, and power it back up. It will still probably beep at you, but eventually you should see the floppy light come on as it boots from the floppy. Wait a minute or two for the floppy to stop, indicating that it has finished running the default.exe program, and then power down your computer. When you then turn it on again, you should hopefully have a working display again, allowing you to change your CMOS settings back, and to change the card's EEPROM settings back to the values you want.

Note that if you don't have DOS handy, you can do the whole method above with a linux boot disk that automatically runs Donald's atlantic program (with the right command line switches) instead of a DOS boot disk that automatically runs the default.exe program.

3Com Cards

The 3Com Etherlink III family of cards (i.e. 3c5x9) can be configured by using another config utility from Donald. You can get the file 3c5x9setup.c from Donald's ftp server, www.scyld.com to configure these cards. (Note that the DOS 3c5x9B config utility may have more options pertaining to the new ``B'' series of the Etherlink III family.)

6.2 Diagnostic Programs for Ethernet Cards

Any of the diagnostic programs that Donald has written can be obtained from his website.

Ethercard Diagnostics

Allied Telesis AT1700 -- at1700.c

Cabletron E21XX -- e21.c

HP PCLAN+ -- hp+.c

Intel EtherExpress -- eexpress.c

PCI NE2000 cards -- ne2k-pci-diag.c

ISA NE2000 cards -- ne2k.c

RealTek (ATP) Pocket adaptor atp-diag.c

All Other Cards -- try typing cat /proc/net/dev and dmesg to see what useful info the kernel has on the card in question.


Next Previous Contents


Партнёры:
PostgresPro
Inferno Solutions
Hosting by Hoster.ru
Хостинг:

Закладки на сайте
Проследить за страницей
Created 1996-2024 by Maxim Chirkov
Добавить, Поддержать, Вебмастеру